E02ZLF (PDF version)
E02 Chapter Contents
E02 Chapter Introduction
NAG Library Manual

NAG Library Routine Document

E02ZLF

Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

+ Contents

    1  Purpose
    7  Accuracy
    9  Example

1  Purpose

E02ZLF is used to query the value of optional parameters available to supported problem solving routines in Chapter E02. Currently, only E02JDF is supported.

2  Specification

SUBROUTINE E02ZLF ( OPTSTR, IVALUE, RVALUE, CVALUE, OPTYPE, IOPTS, OPTS, IFAIL)
INTEGER  IVALUE, OPTYPE, IOPTS(*), IFAIL
REAL (KIND=nag_wp)  RVALUE, OPTS(*)
CHARACTER(*)  OPTSTR, CVALUE

3  Description

E02ZLF is used to query the current values of options. It is necessary to initalize optional parameter arrays using E02ZKF before any options are queried.
E02ZLF will normally return either an integer, real or character value dependent upon the type associated with the optional parameter being queried. Whether the option queried is of integer, real or character type is indicated by the returned value of OPTYPE.
Information on optional parameter names and whether these options are real, integer or character can be found in Section 10 in E02JDF.

4  References

None.

5  Parameters

1:     OPTSTR – CHARACTER(*)Input
On entry: a string identifying the option whose current value is required. See Section 10 in E02JDF for information on valid options. In addition, the following is a valid option:
Identify
E02ZLF returns in CVALUE the routine name supplied to E02ZKF when the optional parameter arrays IOPTS and OPTS were initialized.
2:     IVALUE – INTEGEROutput
On exit: if the optional parameter supplied in OPTSTR is an integer valued parameter, IVALUE will hold its current value.
3:     RVALUE – REAL (KIND=nag_wp)Output
On exit: if the optional parameter supplied in OPTSTR is a real valued parameter, RVALUE will hold its current value.
4:     CVALUE – CHARACTER(*)Output
Note: the maximum length of the string returned in CVALUE depends on the problem solving routine in use. See Section 10.1 of the relevant solver.
On exit: if the optional parameter supplied in OPTSTR is a character valued parameter, CVALUE will hold its current value, unless Identify is specified (see OPTSTR).
5:     OPTYPE – INTEGEROutput
On exit: indicates whether the optional parameter supplied in OPTSTR is an integer, real or character valued parameter and hence which of IVALUE, RVALUE or CVALUE holds the current value.
OPTYPE=1
OPTSTR is an integer valued optional parameter, its current value has been returned in IVALUE.
OPTYPE=2
OPTSTR is a real valued optional parameter, its current value has been returned in RVALUE.
OPTYPE=3
OPTSTR is a character valued optional parameter, its current value has been returned in CVALUE.
6:     IOPTS(*) – INTEGER arrayCommunication Array
On entry: the contents of IOPTS must not have been altered between calls to E02ZKF, E02ZLF and the selected problem solving routine or suite of routines.
7:     OPTS(*) – REAL (KIND=nag_wp) arrayCommunication Array
On entry: the contents of OPTS must not have been altered between calls to E02ZKF, E02ZLF and the selected problem solving routine or suite of routines.
8:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
IFAIL=11
On entry, the optional parameter in OPTSTR was not recognized: OPTSTR=value.
IFAIL=41
On entry, OPTSTR indicates a character optional parameter, but CVALUE is too short to hold the stored value. The returned value will be truncated.
IFAIL=61
On entry, either the option arrays have not been initialized or they have been corrupted.

7  Accuracy

Not applicable.

8  Further Comments

None.

9  Example

See the example programs associated with the problem solving routine you wish to use for a demonstration of how to use E02ZLF to query options.

E02ZLF (PDF version)
E02 Chapter Contents
E02 Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2012