C06RAF (PDF version)
C06 Chapter Contents
C06 Chapter Introduction
NAG Library Manual

NAG Library Routine Document


Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

+ Contents

    1  Purpose
    7  Accuracy

1  Purpose

C06RAF computes the discrete Fourier sine transforms of m sequences of real data values.

2  Specification

REAL (KIND=nag_wp)  X(M*(N+2)), WORK(*)

3  Description

Given m sequences of n-1  real data values xjp , for j=1,2,,n-1 and p=1,2,,m, C06RAF simultaneously calculates the Fourier sine transforms of all the sequences defined by
x^ kp = 2n j=1 n-1 xjp × sin jk πn ,   k= 1, 2, , n-1 ​ and ​ p= 1, 2, , m .
(Note the scale factor 2n  in this definition.)
Since the Fourier sine transform defined above is its own inverse, two consecutive calls of this routine will restore the original data.
The transform calculated by this routine can be used to solve Poisson's equation when the solution is specified at both left and right boundaries (see Swarztrauber (1977)).
The routine uses a variant of the fast Fourier transform (FFT) algorithm (see Brigham (1974)) known as the Stockham self-sorting algorithm, described in Temperton (1983), together with pre- and post-processing stages described in Swarztrauber (1982). Special coding is provided for the factors 2, 3, 4 and 5.

4  References

Brigham E O (1974) The Fast Fourier Transform Prentice–Hall
Swarztrauber P N (1977) The methods of cyclic reduction, Fourier analysis and the FACR algorithm for the discrete solution of Poisson's equation on a rectangle SIAM Rev. 19(3) 490–501
Swarztrauber P N (1982) Vectorizing the FFT's Parallel Computation (ed G Rodrique) 51–83 Academic Press
Temperton C (1983) Fast mixed-radix real Fourier transforms J. Comput. Phys. 52 340–350

5  Parameters

1:     M – INTEGERInput
On entry: m, the number of sequences to be transformed.
Constraint: M1.
2:     N – INTEGERInput
On entry: one more than the number of real values in each sequence, i.e., the number of values in each sequence is n-1.
Constraint: N1.
3:     X( M×N+2 ) – REAL (KIND=nag_wp) arrayInput/Output
On entry: the data must be stored in X as if in a two-dimensional array of dimension 1:M,1:N+2; each of the m sequences is stored in a row of the array. In other words, if the n-1 data values of the pth sequence to be transformed are denoted by xjp, for j=1,2,,n-1 and p=1,2,,m, then the first mn-1 elements of the array X must contain the values
x11 , x12 ,, x1m , x21 , x22 ,, x2m ,, x n-1 1 , x n-1 2 ,, x n-1 m .
The nth to n+2th elements of each row xnp ,, x n+2 p , for p=1,2,,m, are required as workspace. These 3m elements may contain arbitrary values as they are set to zero by the routine.
On exit: the m Fourier sine transforms stored as if in a two-dimensional array of dimension 1:M,1:N+2. Each of the m transforms is stored in a row of the array, overwriting the corresponding original sequence. If the n-1 components of the pth Fourier sine transform are denoted by x^kp, for k=1,2,,n-1 and p=1,2,,m, then the mn+2 elements of the array X contain the values
x^11 , x^12 ,, x^1m , x^21 , x^22 ,, x^2m ,, x^ n-1 1 , x^ n-1 2 ,, x^ n-1 m , 0 , 0 , , 0  3m times .
4:     WORK(*) – REAL (KIND=nag_wp) arrayWorkspace
Note: the dimension of the array WORK must be at least M×N + 2×N + 15.
The workspace requirements as documented for C06RAF may be an overestimate in some implementations.
On exit: WORK1 contains the minimum workspace required for the current values of M and N with this implementation.
5:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
On entry,M<1.
On entry,N<1.
An unexpected error has occurred in an internal call. Check all subroutine calls and array dimensions. Seek expert help.

7  Accuracy

Some indication of accuracy can be obtained by performing a subsequent inverse transform and comparing the results with the original sequence (in exact arithmetic they would be identical).

8  Further Comments

The time taken by C06RAF is approximately proportional to nm logn, but also depends on the factors of n. C06RAF is fastest if the only prime factors of n are 2, 3 and 5, and is particularly slow if n is a large prime, or has large prime factors.

9  Example

This example reads in sequences of real data values and prints their Fourier sine transforms (as computed by C06RAF). It then calls C06RAF again and prints the results which may be compared with the original sequence.

9.1  Program Text

Program Text (c06rafe.f90)

9.2  Program Data

Program Data (c06rafe.d)

9.3  Program Results

Program Results (c06rafe.r)

C06RAF (PDF version)
C06 Chapter Contents
C06 Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2012