S17AHF (PDF version)
S Chapter Contents
S Chapter Introduction
NAG Library Manual

NAG Library Routine Document

S17AHF

Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

+ Contents

    1  Purpose
    7  Accuracy

1  Purpose

S17AHF returns a value of the Airy function, Bix, via the function name.

2  Specification

FUNCTION S17AHF ( X, IFAIL)
REAL (KIND=nag_wp) S17AHF
INTEGER  IFAIL
REAL (KIND=nag_wp)  X

3  Description

S17AHF evaluates an approximation to the Airy function Bix. It is based on a number of Chebyshev expansions.
For x<-5,
Bix=atcosz+btsinz-x1/4,
where z= π4+ 23-x3 and at and bt are expansions in the variable t=-2 5x 3-1.
For -5x0,
Bix=3ft+xgt,
where f and g are expansions in t=-2 x5 3-1.
For 0<x<4.5,
Bix=e11x/8yt,
where y is an expansion in t=4x/9-1.
For 4.5x<9,
Bix=e5x/2vt,
where v is an expansion in t=4x/9-3.
For x9,
Bix=ezutx1/4,
where z= 23x3 and u is an expansion in t=2 18z-1.
For x<machine precision, the result is set directly to Bi0. This both saves time and avoids possible intermediate underflows.
For large negative arguments, it becomes impossible to calculate the phase of the oscillating function with any accuracy so the routine must fail. This occurs if x<- 32ε 2/3, where ε is the machine precision.
For large positive arguments, there is a danger of causing overflow since Bi grows in an essentially exponential manner, so the routine must fail.

4  References

Abramowitz M and Stegun I A (1972) Handbook of Mathematical Functions (3rd Edition) Dover Publications

5  Parameters

1:     X – REAL (KIND=nag_wp)Input
On entry: the argument x of the function.
2:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
IFAIL=1
X is too large and positive. On soft failure, the routine returns zero. (see the Users' Note for your implementation for details)
IFAIL=2
X is too large and negative. On soft failure, the routine returns zero. See also the Users' Note for your implementation.

7  Accuracy

For negative arguments the function is oscillatory and hence absolute error is the appropriate measure. In the positive region the function is essentially exponential-like and here relative error is appropriate. The absolute error, E, and the relative error, ε, are related in principle to the relative error in the argument, δ, by
E x Bix δ,ε x Bix Bix δ.
In practice, approximate equality is the best that can be expected. When δ, ε or E is of the order of the machine precision, the errors in the result will be somewhat larger.
For small x, errors are strongly damped and hence will be bounded essentially by the machine precision.
For moderate to large negative x, the error behaviour is clearly oscillatory but the amplitude of the error grows like amplitude Eδ x5/4π .
However the phase error will be growing roughly as 23x3 and hence all accuracy will be lost for large negative arguments. This is due to the impossibility of calculating sin and cos to any accuracy if 23x3> 1δ .
For large positive arguments, the relative error amplification is considerable:
εδx3.
This means a loss of roughly two decimal places accuracy for arguments in the region of 20. However very large arguments are not possible due to the danger of causing overflow and errors are therefore limited in practice.

8  Further Comments

None.

9  Example

This example reads values of the argument x from a file, evaluates the function at each value of x and prints the results.

9.1  Program Text

Program Text (s17ahfe.f90)

9.2  Program Data

Program Data (s17ahfe.d)

9.3  Program Results

Program Results (s17ahfe.r)


S17AHF (PDF version)
S Chapter Contents
S Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2012